- 1972-1975 H2 750
- 1973-1975 Z1 900
- 1976-1977 KZ900A
- May fit others
-
Bearings to fit rear brake hub and sprocket carrier. Kit P/N: 0215-0830 Replaces Kawasaki P/N's: 1) 601B6304Z Bearing 1) 601B6304 Bearing 1) 601B6206 Bearing 1) 92050-027 Seal Applications: -
Highest Quality Reproduction Replacement Part. Made in Japan. Replaces Kawasaki P/N: 92066-017 Our P/N 15-7588 ~includes 4 plugs~ Applications:- 73-75 Z1 900
- 76-77 Kz900A
- 1976- Kz900B LTD
- 77-80 Kz1000A
- 77-80 Kz1000B LTD
- 78 & 80 Kz1000D Z1R
- 78-81 Kz1000C Police
- 79-80 Kz1000E Shaft
- 1980 Kz1000-G1 Classic
-
Footrest bar cap. Zinc Plated Sold as a set of 4 Quality part made in the USA Replaces Kawasaki P/N: 92102-010 Applications:- Z1 900
- KZ900 LTD
- KZ900A
- Z1R
- KZ1000A 77-80
- KZ1000LTD 77-80
- KZ750B 76-79
- KZ650
-
High Quality Reproduction Part Made in the U.S.A. Replaces Kawasaki P/N:42045-018 Nut 18mm 550D4035 Pin Applications:- 73-75 Z1 900
- 76-77 KZ900A
- 1976 KZ900B LTD
- 72-75 H2 750 Triple
- 77-80 KZ1000A
- 76-79 KZ750B
-
Quality Reproduction Part Replaces Kawasaki P/N: 56014-049 Manufacturers P/N: KFR17-93700 Kit Contains: (1) 56014-049 right emblem (1) 56013-054 left emblem (4) 92012-003 screws Applications:- 74-75 Z1 900
- 76-77 KZ900A
- 77-78 KZ1000A
- *May Fit Others
-
This kit is made up of good quality parts, including Motion Pro fuel line. Because of the size of the Pingel fuel valve, we had to use the single outlet so that it would not interfere with the stock Z1 side cover. Quality parts for a quality fuel valve. Kit Contains:- (1) fuel line 2FT Motion Pro
- (4) 5/16 clips
- (2) 1/4 clips
- (1) T line
-
Carburetor Holder Set - Left & Right Quality Made Reproduction Part Replaces Kawasaki P/N's: (2) 16065-028 Right (2) 16065-029 Left (4) 92068-006 Rubber Plug Applications:- 1973-1975 Z1 900
- 1976-1977 KZ900 All
- 1977-1980 KZ1000 All
-
Set of 2 Rear Passenger Foot Peg Rubbers Highest Quality Reproduction! Replaces Kawasaki P/N: 92076-009 Applications:- A1, A1SS
- A7, A7SS
- H1 500, H1C
- W1, W1SS
- W2SS, W2TT
-
Out of stock
Chrome Exhaust Clamp Set of 2 Quality Japanese Made Reproduction Part Replaces Kawasaki P/N: 92037-103 Sold as Shown (set of 2) Applications:- 73-75 Z1 900
- 76-77 KZ900 A
-
This is an exact replica of the original master cylinder ribbed rubber dust cover. Replaces Kawasaki P/N: 43069-001 Our P/N: 11224 Applications:- 73-75 Z1 900
- 76-77 KZ900 A
- 1976 KZ900 LTD
- EARLY KZ400
- 77-78 KZ1000 LTD
- EARLY KZ1000 POLICE
- Will fit others
-
Quality Reproduction Part Replaces Kawasaki P/N: 56018-261 Kit contains both left and right emblems Lock nuts P/N: 92018-005 Application:- 77-78 KZ1000A
-
Quality reproduction, replaces Kawasaki P/N's: 92075-078 Rubber Damper (Kit contains 4) 92075-146 Rubber Damper (Kit contains 2) 92075-141 Rubber Damper (Kit contains 2) Also comes with 2 6mm bolts and washers, as shown Our P/N: 10808 Application:- Z1 900
- Will fit many more
-
Kit Contains: 2) 92001-038 Bolt 12mm head, 2) 312B0800 13mm nut Applications:- 73-74 Z1 900
- 69-72 H1 500
- A1 & A155 250 Twin
- A7 & A755 350 Twin
- May fit others
-
Out of stock
Will replace the following part #s 69-74 CB750:- 33400-341-702
- 33450-341-702
- 33650-300-000
- 33610-300-000
- Will fit others
-
These are the petcocks we use on all of our special project bikes. Replaces Kawasaki P/N: 51023-040 Kit includes: (1) 8210-T-AH Petcock (1) A2002C Adapter 24mm Applications:- H2 750
- H1 500
- KH 500
-
Out of stock
Quality Made in Japan Gasket Set Set of 4 Replaces KAWASAKI P/N: 16019-031 Applications:- 77-80 KZ1000A
- 77-80 KZ1000 LTD
- 78 & 80 Z1R
- 79-80 KZ1000E SHAFT
- Early KZ650